Building a Garden Railway in O Gauge_Pt2- The Rockery

This forum is for the discussion of railway modelling of the LNER and its constituent companies.

Moderators: 52D, Rlangham, Atlantic 3279, Blink Bonny, Saint Johnstoun, richard, Tom F

Post Reply
GeoffB
NER J27 0-6-0
Posts: 134
Joined: Tue Oct 18, 2005 10:15 pm
Location: Cleethorpes, Lincolnshire, UK

Building a Garden Railway in O Gauge_Pt2- The Rockery

Post by GeoffB » Wed May 31, 2006 2:16 am

Hi All,

To continue - this is a bit about the rockery section. The rockery came about due to a large wall being nocked out of the workshop - the rubble had to go somewhere - build a rockery on it! And the fact that the 5" GL line - I wanted a wooden bridge - so a pond had to be dug - the soil for the rockery!!

The O Gauge line had to be moved to accomodate the 5" line so where better to take it thatn across the rockery to be?

The Piccies show some of the stages in the construction of the line across the rocks. The last pics were shot today - the under arches have still to be put in place, but I am giving the cement a week to get up to a decent strength before I put them in place (cementious material takes 28 days to achieve a maximum strength, apparently!).

Next stop - the bridges! The one for the waterfall area is about half finished at present.

More later.

GeoffB
Attachments
WallTops_Finished_DSCF3118.jpg
The wall tops are finished - next stop - the arches
WallTops_Finished_DSCF3118.jpg (89.47 KiB) Viewed 2294 times
WestEndArches_DSCF4495.jpg
West end arches
WestEndArches_DSCF4495.jpg (95.87 KiB) Viewed 2276 times
SouthEndArch_DSCF4488.jpg
South End arch - this is shaped to accept a low span bridge from the end nearest the camera
SouthEndArch_DSCF4488.jpg (92.24 KiB) Viewed 2266 times
ViewFromWestEnd_DSCF4499.jpg
View from the West end
ViewFromWestEnd_DSCF4499.jpg (94.58 KiB) Viewed 2264 times
ViewFromSouthEnd_DSCF4502.jpg
View from South end of the curve
ViewFromSouthEnd_DSCF4502.jpg (100.37 KiB) Viewed 2267 times

GeoffB
NER J27 0-6-0
Posts: 134
Joined: Tue Oct 18, 2005 10:15 pm
Location: Cleethorpes, Lincolnshire, UK

Post by GeoffB » Wed May 31, 2006 2:26 am

The earlier views in the construction.

GeoffB
Attachments
Rockery_ClsUp_bsboards-dscf.jpg
Close up of the fitting of the boards
Rockery_ClsUp_bsboards-dscf.jpg (93.84 KiB) Viewed 2262 times
Rockery_bsboards_fitted-dsc.jpg
General view of the fitted baseboards
Rockery_bsboards_fitted-dsc.jpg (108.54 KiB) Viewed 2271 times
Rockery_allboards_fitted-ds.jpg
The rockery with all baseboards fitted ready for the wall tops and arches to be added. Note 5" on the wooden bridge in foreground
Rockery_allboards_fitted-ds.jpg (87.92 KiB) Viewed 2263 times
WallTops_DSCF4306.jpg
The cast wall tops
WallTops_DSCF4306.jpg (56.81 KiB) Viewed 2279 times
WallTops_Assy_with_Jigs_DSC.jpg
The wall tops jigged in place whilst cementing
WallTops_Assy_with_Jigs_DSC.jpg (81.26 KiB) Viewed 2288 times

GeoffB
NER J27 0-6-0
Posts: 134
Joined: Tue Oct 18, 2005 10:15 pm
Location: Cleethorpes, Lincolnshire, UK

Post by GeoffB » Wed May 31, 2006 2:34 am

An exercise in civil engineering in miniature!
The concrete bases have been constructed complete with the baseboard supports and drainage ready for the fitting of the boards. The waterfall and the rockery have yet to be added after all the bricks have been "sifted" out of the soil!

Still very much a builder's tip!

GeoffB
Attachments
Rockery-Start-dscf1982.jpg
Bases ready to accept the baseboards.
Rockery-Start-dscf1982.jpg (90.76 KiB) Viewed 2258 times

User avatar
richard
LNER A4 4-6-2 'Streak'
Posts: 3303
Joined: Thu Sep 01, 2005 5:11 pm
Location: Wichita Falls, Texas
Contact:

Post by richard » Wed May 31, 2006 2:59 am

Good progress!

What were the baseboards made of?

Cement curing times: Yep, that's why with skyscrapers, they'll keep the wooden bracing in place for a few floors after the shuttering and pouring has been done.
A few years back, New Scientist had a pie-in-the-sky feature article about using magnesium-rich cement and concretes as carbon dioxide sinks. I think they said it would still be curing and taking CO2 from the atmosphere after two years! I don't think the quantities worked out (how much concrete would you have to lay to make a dent in atmospheric CO2?) and I have never heard anything since.

Richard
Richard Marsden
LNER Encyclopedia

GeoffB
NER J27 0-6-0
Posts: 134
Joined: Tue Oct 18, 2005 10:15 pm
Location: Cleethorpes, Lincolnshire, UK

Post by GeoffB » Wed May 31, 2006 11:16 am

Hi Richard,

The baseboards are made from 18mm ply covered with roofing felt. I use OSD most times as it is quite stable and as it is not in layers, it doesn't part plys - and it is half the price!.

A quick guide to this in case anyone is interested in starting a garden layout. If you've done it, then, sorry - not trying to teach "sucking eggs"! Just giving another approach to the idea.

The boards are cut to size and shape, then the edges are rounded off (with a router) both sides to give a complete roll edge which allows the roofing felt (coarse grit type) to be rolled over the edge without splitting. I usually lay the felt out on the lawn on a warm, sunny day (the odd one or two that sometimes arrive in the typical British summer - remember them, Richard?) to get the felt pliable.

The felt is then cut to shape, laid on the baseboard that has been screwed in place on the 4x2 batterns and then rolled over the edge and tacked into place with large head roofing tacks.

The joints are sealed with black silicon sealer and the grit that comes off the felt is collected up and sprinkled very liberally onto the wet silicon and left till the silicon has gone off - I usually give it a day - then the surplus is swept off and kept for the next joint. Apart from the boards that went around the rockery, I usually try to cut the board joints at an angle which tends to alleviate "stepping" and try to keep the felt joints away from the board joints. I cut the felt joints at an angle too, as they are easier to disguise.

In the case of the boards around the rockery, as they were to be screwed to the support bricks, the felt was applied first by laying face down and the board positioned upside down on the felt, the felt rolled over, then tacked to the underside (which is facing upwards). Then board was then put in place with the screws going through the felt and the silicon/grit treatment applied to seal.

Regards,

Geoff

Post Reply