Make do and Mend - And a New Horsebox

This forum is for the discussion of railway modelling of the LNER and its constituent companies.

Moderators: 52D, Rlangham, Atlantic 3279, Blink Bonny, Saint Johnstoun, richard, Tom F

drmditch
NER C7 4-4-2
Posts: 864
Joined: Sun Aug 01, 2010 5:55 pm
Location: Durham

Re: Make do and Mend - Running Late for Winter

Post by drmditch » Wed Apr 03, 2019 5:04 pm

Dave wrote:
Wed Apr 03, 2019 9:16 am
Very nice looking model, I like the finish, it's hard to replicate convincingly.
Thank you. I'm still not entirely convinced about the base colour, but I am reasonably happy with the attempts at layers of rust and dirt.
When I get round to building the second one of the pair, I might assume it's been freshly repainted.

Did the LNER continue to use Oxford Blue up till 1940 or so?

Chas Levin
LNER J94 0-6-0ST Austerity
Posts: 39
Joined: Fri Apr 10, 2015 11:54 am
Location: London

Re: Make do and Mend - Running Late for Winter

Post by Chas Levin » Thu Apr 18, 2019 11:24 am

Love that bridge - superb, and very inspiring :D (as is the snowplough too!)
Chas

Hatfield Shed
LNER P2 2-8-2
Posts: 952
Joined: Fri Dec 23, 2011 3:34 pm

Re: Make do and Mend - Running Late for Winter

Post by Hatfield Shed » Thu Apr 18, 2019 12:19 pm

drmditch wrote:
Wed Apr 03, 2019 5:04 pm
...Did the LNER continue to use Oxford Blue up till 1940 or so?
I wasn't there (!) but the impression I have formed from the limited colour photographic evidence is that existing stocks of supplies at outbreak of war were sensibly used until finished.

drmditch
NER C7 4-4-2
Posts: 864
Joined: Sun Aug 01, 2010 5:55 pm
Location: Durham

Re: Make do and Mend - Running Late for Winter

Post by drmditch » Sun Jul 21, 2019 4:33 pm

My railway is making progress, but I've been a bit distracted of late preparing for ....this.....

If you do visit Locomotion when I'm doing these (on the 26th July and 1st and 8th August) do make yourself known!
(Preferably politely!)

I'm a bit fed up with railway wiring, so need to work on something more interesting now!

More posts in due course!

MikeTrice
LNER Thompson B1 4-6-0 'Antelope'
Posts: 619
Joined: Sat Apr 03, 2010 4:45 pm

Re: Make do and Mend - Running Late for Winter

Post by MikeTrice » Sun Jul 21, 2019 5:40 pm

It would be good if you could get some nice detailed photos. I saw FS at the NRM earlier in the year (after meeting you at Shildon) and it was not very accessible.

drmditch
NER C7 4-4-2
Posts: 864
Joined: Sun Aug 01, 2010 5:55 pm
Location: Durham

Re: Make do and Mend - Running Late for Winter

Post by drmditch » Sun Jul 21, 2019 6:20 pm

MikeTrice wrote:
Sun Jul 21, 2019 5:40 pm
It would be good if you could get some nice detailed photos. I saw FS at the NRM earlier in the year (after meeting you at Shildon) and it was not very accessible.
I will try. There will be some days when the locomotive will be standing on the apron, rather than alongside the platform or running (short) trains.
Was there any particular feature you wanted to see?

MikeTrice
LNER Thompson B1 4-6-0 'Antelope'
Posts: 619
Joined: Sat Apr 03, 2010 4:45 pm

Re: Make do and Mend - Running Late for Winter

Post by MikeTrice » Sun Jul 21, 2019 6:36 pm

Not particularly. It is one of those situations when you never know if a photograph is going to prove useful or not. A bit like I did for Green Arrow.

drmditch
NER C7 4-4-2
Posts: 864
Joined: Sun Aug 01, 2010 5:55 pm
Location: Durham

Re: Make do and Mend - Running Late for Winter

Post by drmditch » Mon Jul 22, 2019 12:28 am

I will try to take a selection!

drmditch
NER C7 4-4-2
Posts: 864
Joined: Sun Aug 01, 2010 5:55 pm
Location: Durham

Re: Make do and Mend - And a New Horsebox

Post by drmditch » Sat Oct 05, 2019 4:16 pm

I don't normally post my ordinary kit builds here, not trusting my normal standard of model-making. However, I needed a break from construction and wiring and planning diode matrices, so I raided my kit box for something interesting and made this:-
Post_03.JPG
The Parkside kit for the LNER Dia.D5 Horsebox has been around for a while, and Mick B has shown his ...here... and Jwealleans (second ?) build ...here...

I found it went together quite well, as with most Parkside kits in my experience, however I did make the following alterations:-
- packing the solebars out from the cross-members by about .75mm on each side. This makes the wheels run much easier and avoids the classic
problem of the w-irons leaning inwards as the solvent dries.
- replacing the lower footsteps with a brass and copper construction. The plastic supplied seemed a bit 'femmer'.
- making up underframe details to what is now my usual specification. This is not as good as Mick B's, but it looks adequate from the side. (I try to
avoid looking at my wagons upside down!) I always like to make the cross-shaft fairly thick (I think they were about 2.5" diameter) For this I use
insulation stripped from layout wire. I also like to add safety loops and remove the plastic flat moulded items.
- the brake blocks on this kit are supplied as separate and rather fiddly mouldings. These are difficult to fit in a good position, and on 6 out of the 8 I
have got too large a gap between them and the wheels. More thought would have suggested some kind of sub-assembly to make fitting easier. I did
consider using some of the Mainly Trains LNER etches I have in stock, but I am saving those for a future project!
Post_02.JPG
I also modified the body moulding slightly:-
- carving away the moulded handrails and door handles and replacing them in brass.
- modifying the lamp irons
- fitting seat and door detail in the grooms compartment. (which is hardly visible when the roof is on!)
Post_2A.JPG
The glazing is tricky, as Mr Wealleans also comments on. It needs to be done after painting and it would it have been easier if I'd added the compartment partitions afterwards. I should have replaced the material in the kit, which seems to damage quite easily, with the normal acrylic that I use. (It might be just that I've had the kit for ages). For the lavatory window I abraded the inner surface of the window with a glass-fibre brush and fine glass-paper. Before fitting the roof I added white electrical tape to the inside of the compartment. This avoided the problems of paint leaking through!

I used Mr Tatlow's NPCS book as a reference, but that does not help with the lettering. I didn't like the instructions in the kit and couldn't find any other photographs in LNER condition. I appealed for help on Mick B's thread and JASd17 was able to help ... here... . On the following page he was also able to supply a picture.

This was also useful for showing an additional brake control (?) pipe on the compartment end. I managed to fit a representation of this without damaging the almost finished model.
Post_08.JPG
There has been discussion in the past about the colour of LNER Brown paint ...here...

Unfortunately some of my favourite artists acrylic pots have dried out and the different brand I used doesn't have quite the same effect. Once the lettering I am ordering from Precision Labels (Mr Peck is being most helpful.) I may try some method of varnishing - very carefully!
I have still to fit the lower door springs. The plastic ones would be a bit weak and I will make a metal replacement.

This forum and it's members are a splendid resource. Thank you everybody!

drmditch
NER C7 4-4-2
Posts: 864
Joined: Sun Aug 01, 2010 5:55 pm
Location: Durham

Re: Make do and Mend - And a New Horsebox

Post by drmditch » Thu Nov 07, 2019 12:25 pm

Sorry for a further post on an 'ordinary' kit build.

Here is the finished vehicle, showing the products of Precision Labels, and a coat of silk finish acrylic varnish.
Post_10.JPG
Last edited by drmditch on Tue Nov 12, 2019 4:57 pm, edited 1 time in total.

exile
LNER J94 0-6-0ST Austerity
Posts: 47
Joined: Mon Oct 26, 2015 10:58 pm
Location: France

Re: Make do and Mend - And a New Horsebox

Post by exile » Thu Nov 07, 2019 12:42 pm

Why apologise? Very nice looking model.

drmditch
NER C7 4-4-2
Posts: 864
Joined: Sun Aug 01, 2010 5:55 pm
Location: Durham

Re: Make do and Mend - And a New Horsebox

Post by drmditch » Tue Nov 12, 2019 4:58 pm

exile wrote:
Thu Nov 07, 2019 12:42 pm
Why apologise? Very nice looking model.
Thank you - but it wasn't a very good picture.
I've replaced it (12/11/19) with a marginally better one.

Post Reply