Looking for Graeme King parts for an A2/1

Post your private sales and wants adverts here!

Moderators: 52D, Rlangham, Atlantic 3279, Blink Bonny, Saint Johnstoun, richard, Tom F

Post Reply
AlexH
NER Y7 0-4-0T
Posts: 2
Joined: Fri May 31, 2019 4:44 pm

Looking for Graeme King parts for an A2/1

Post by AlexH » Fri May 31, 2019 5:17 pm

Hello everyone.

I'm looking for Graeme King resin parts for an A2/1 that I'm building. I've looked around online as to where I can buy the parts and I'm told that I can get in contact with Graeme on this website and purchase the parts. I am rather new to this website, does anyone know if these parts are these parts still for available? And if so how much do they cost?

Any help would be appreciated. Thank you.

Dave S
LNER J39 0-6-0
Posts: 153
Joined: Wed Dec 14, 2016 12:46 pm

Re: Looking for Graeme King parts for an A2/1

Post by Dave S » Fri May 31, 2019 6:36 pm

Graeme is a member of the site, but he is in sunnier climes at present, sipping a fancy cocktail while being fanned by a harem of nubile women.

No doubt he will respond when he recovers.

User avatar
teaky
NBR D34 4-4-0 'Glen'
Posts: 271
Joined: Sun May 04, 2008 8:56 pm

Re: Looking for Graeme King parts for an A2/1

Post by teaky » Fri May 31, 2019 8:57 pm

Not if his wife finds out, he won't. :D

jwealleans
LNER A4 4-6-2 'Streak'
Posts: 3479
Joined: Wed Oct 25, 2006 8:46 am

Re: Looking for Graeme King parts for an A2/1

Post by jwealleans » Sat Jun 01, 2019 5:37 pm

I have no doubt she's on the next recliner along with bronzed and oiled Adonii pandering to her every whim.

User avatar
Atlantic 3279
LNER A4 4-6-2 'Streak'
Posts: 5335
Joined: Fri Jun 26, 2009 9:51 am
Location: 2850, 245

Re: Looking for Graeme King parts for an A2/1

Post by Atlantic 3279 » Wed Jun 05, 2019 1:59 pm

Hello Alex, I'm back!

I'll send you a private message via this forum in due course, containing my e-mail address, although I'm not sure whether you'll need to post a few more entries on the forum before you are able to get access to the PM. Once I have your e-mail address too, I can send you full details. Publishing e-mail addresses on the open part of the forum isn't a good idea, for obvious reasons. Equally, the PM system has to be restricted to limit the ability of robots to send rubbish to all forum members.

If you want the information more quickly and you can "de-code" an e-mail address sent out in the characters of the NATO alphabet, I can try that instead......

Graeme King
Most subjects, models and techniques covered in this thread are now listed in various categories on page1

Dec. 2018: Almost all images that disappeared from my own thread following loss of free remote hosting are now restored.

User avatar
richard
LNER A4 4-6-2 'Streak'
Posts: 3284
Joined: Thu Sep 01, 2005 5:11 pm
Location: Wichita Falls, Texas
Contact:

Re: Looking for Graeme King parts for an A2/1

Post by richard » Wed Jun 05, 2019 2:19 pm

I think he'll be able to read your PM but not reply until he has had the usual 5 posts approved.

Richard
Richard Marsden
LNER Encyclopedia

AlexH
NER Y7 0-4-0T
Posts: 2
Joined: Fri May 31, 2019 4:44 pm

Re: Looking for Graeme King parts for an A2/1

Post by AlexH » Thu Jun 06, 2019 12:17 pm

Hi,
Thanks I'll check my messages and send an email.

User avatar
Atlantic 3279
LNER A4 4-6-2 'Streak'
Posts: 5335
Joined: Fri Jun 26, 2009 9:51 am
Location: 2850, 245

Re: Looking for Graeme King parts for an A2/1

Post by Atlantic 3279 » Sat Jun 08, 2019 10:50 am

Received, and informative response sent.
Most subjects, models and techniques covered in this thread are now listed in various categories on page1

Dec. 2018: Almost all images that disappeared from my own thread following loss of free remote hosting are now restored.

Post Reply