border image border image
 
           
 
   
border image border image
border image border image
 
B 4-6-0 Tender
B1
B2
B3
B4
B5
B6
B7
B8
B9
B12
B13
B14
B15
B16
B17
B18
B19
B1 Thompson
B2 Thompson

The Robinson Class B3 (GCR Class 9P) "Lord Faringdon" 4-6-0s

Robinson Class B3 No. 6164 'Earl Beatty' (M.Morant)

The Class 9P 4-6-0s were Robinson's largest passenger locomotive design. The first locomotive was built at the end of 1917 and named after the then Great Central Railway's (GCR) chairman Lord Faringdon. It is said to have been inspired by the London & North Western Railway's (LNWR) 'Claughton' class, although they had little in common other than they both had four cylinders.

Unusually for a British four cylinder design, the B3s had Stephenson valve gear. The cranks for the inside cylinders were 180 degrees apart from their adjacent outside cylinders. Each outside cylinder was driven by the same set of valve gear as the adjacent inside cylinder. This was achieved using a rocking motion and different admission arrangements for the cylinders. The outside cylinders had outside admission, and the inside cylinders had inside admission. The two inside cylinders had cranks 90 degrees apart.

The inside cylinders drove the front axle, whilst the outside cylinders drove the second axle. This divided drive solved the problem of the restricted bearings on the driving axle on the B2 'Sir Sam Fay' Class. The B3s had a similar boiler to the B2s, and had a similar general appearance, although the outside cylinders gave them a more 'heavy' appearance.

After the end of World War 1, five more B3s were built in 1920. With Grouping in 1923, none of the B3s were cut down to the Composite LNER loading gauge, although over time they acquired Doncaster pattern chimneys and low-dome boilers.

Although more successful than the B2s, the B3s were not a huge success. They could be fast and powerful, but they tended to burn large amounts of coal.

In an attempt to improve the coal burning, Gresley rebuilt Nos. 6166 & 6168 with Caprotti valve gear in 1929; and Nos. 6164 & 6167 in 1938-39. The main difference with the locomotives with the Caprotti valve gear, was that the poppet valves were mounted vertically. There were two valves at each end of each cylinder: one for admission and one for exhaust. Hence the Caprotti B3s had a total of sixteen valves. The valves were then operated by a cam system operated from the main drive axle. Caprotti valve gear had the advantage that the periods of of release and compression could be kept constant for any degree of cut-off. This resulted in more work from the expansion of steam, and a reduction in the volume to be cleared. Tests with the first two locomotives demonstrated a saving in coal of 16 percent. The cam operating scrolls would often fail, but, but this was fixed with bronze scrolls. The valve cam boxes also tended to overheat. This was eventually fixed by completely removing the covers on the boxes. The rebuilt engines were classified B3/2, whilst the original Stephenson engines were classified B3/1.

Thompson rebuild of Class B3 No. 6166 (M.Peirson)

In 1943, Thompson rebuilt No. 6166 to be very similar to one of his B1s and was reclassified B3/3. Only the bogie, driving wheels and the rear part of the frame were kept in the rebuild. The rebuild was too drastic, and the B3/3 regularly suffered from cracked frames. All further B3 rebuilds were cancelled.

The first locomotive, No. 1169 Lord Faringdon was initially allocated to Gorton. Three years later when the other five members of the class were built, they were allocated to Gorton and Immingham. No. 1169 also moved to Immingham. Immingham had very little passenger traffic, so this allocation is a sign that the B3s were not the best of passenger locomotives. The Gorton locomotives hauled the slower services to London. The slower services would have many stops, and no doubt the B3's four cylinders and six coupled wheels were a distinct advantage for accelerating from rest.

After Grouping in 1923, a home for the B3s was found on the GN (Great Northern) Section. They were allocated to the Copley Hill and Kings Cross sheds and operated a newly introduced Pullman service between Kings Cross and Leeds. Replacing the free-steaming Ivatt Atlantics, the B3s gave the GN crews a lot of problems. Some engine crews did have success though.

In 1927, three B3s moved to Neasden, and three returned to Gorton. The Neasden locomotives regularly worked the two night trains from Marylebone to Manchester and Liverpool, as far Leicester. This pattern continued until 1939. The Gorton locomotives quickly moved to Immingham. Here they ran a midday passenger service between Cleethorpes and Leicester, on another schedule that would remain constant until 1939.

The B3s were used on a variety of services during World War 2, often standing in for four-coupled types that were having trouble keeping time with the increasing loads.

With the failure of the B3/3 rebuild, it was decided to withdraw the B3s once wartime motive power pressures had lessened. Withdrawals of the B3/1s and B3/2s started in September 1946 and were complete by the end of 1947. The rebuilt B3/3 was withdrawn in 1949.

Technical Details

No. 1169 Lord Faringdon had a different boiler specification to the other B3s, and has been given its own column in the following table:

No. 1169 Nos. 1164-8
Cylinders (x4): 16x26in. 16x26in.
Motion: Gear: Stephenson Stephenson
Valves: 8in piston 8in piston
Boiler: Max. Diameter: 5ft 6in 5ft 6in
Pressure: 180psi 180psi
Diagram No.: 13 13
Heating Surface: Total: 2477 sq.ft. 2387 sq.ft.
Firebox: 163 sq.ft. 163 sq.ft.
Superheater: 294 sq.ft. (24x 1.06in dia) 343 sq.ft. (28x 1.06in dia)
Tubes: 1442 sq.ft. (139x 2.25in dia) 1203 sq.ft. (116x 2.25in dia)
Flues: 578 sq.ft. (24x 5.25in dia) 678 sq.ft. (28x 5.25in dia)
Grate Area: 26 sq.ft. 26 sq.ft.
Wheels: Leading: 3ft 6in 3ft 6in
Coupled: 6ft 9in 6ft 9in
Tender: 4ft 4in 4ft 4in
Tractive Effort: (@ 85%) 25,145lb 25,145lb
Wheelbase: Total: 52ft 9.5in 52ft 9.5in
Engine: 28ft 10in 28ft 10in
Tender: 13ft 0in 13ft 0in
Weight (full): Total: 127 tons 8cwt 127 tons 8cwt
Engine: 79 tons 2cwt 79 tons 2cwt
Tender: 48 tons 6cwt 48 tons 6cwt
Max. Axle Load: 20 tons 20 tons

Preservation

None of the B3s survived into preservation.

Models

Bill Bedford produces a 4mm scale (OO gauge) body kit of the B3/3.

Great Central Models have a 4mm (P4,EM) scale etched brass kit of the B3 planned for the near future.

David Andrews Locomotive Kits produce a kit of the B3 for O gauge (7mm scale).

Locomotives

No. 6167 Lloyd George lost its nameplates on the orders of Sir Frederick Banbury, during August 1923. The nameplates were lost until 1963 when Kings Cross Top Shed was being demolished, and they were found behind a partition.

No. 6166 Earl Haig lost its nameplates when it was rebuilt during October 1943, due to the lack of a suitable place on the new locomotive for the old plates. No. 6166 was the only B3 to survive into BR ownership and was given the BR number of 61497 in April 1948.

None of the B3s carried their numbers from the first 1946 re-numbering. The 1946 numbers listed here are from the second re-numbering.

LNER No.1946 No.Build DateRebuilt as B3/2Rebuilt as B3/3Disposal DateName
6169149411/1917--12/1947Lord Faringdon
616414956/19206/1939-9/1947Earl Beatty
616514967/1920--12/1947Valour
616614978/192012/192910/19434/1949Earl Haig
616714989/19206/1938-12/1947Lloyd George
6168(1499)10/19209/1929-9/1946Lord Stuart of Wortley

Acknowledgements

Thank you to the Mike Morant Collection for the photograph of B3 No. 6164 Earl Beatty.

Thank you to Malcolm Peirson for the photograph of the Thompson-rebuilt No. 6166.



 
border image border image